{"product_id":"5015-blower-hepa-exhaust-for-voron-0-2","title":"5015 Blower HEPA Exhaust for Voron 0.2","description":"\u003cp\u003eThis model adapts \u003ca target=\"_blank\" rel=\"noopener noreferrer ugc\" href=\"https:\/\/www.printables.com\/model\/1073729-5015-blower-hepa-exhaust-for-voron-trident-horizon\"\u003eRagingRoosevelt's Voron Trident exhaust\u003c\/a\u003e to fit the V0.2 with \u003cstrong\u003e100mm\u003c\/strong\u003e top-hat. Air exhausted from the chamber is passed through a HEPA filter, but not through an activated carbon layer, so it is recommended to pair this with a recirculating air-scrubber like the \u003ca target=\"_blank\" rel=\"noopener noreferrer ugc\" href=\"https:\/\/github.com\/zruncho3d\/zerofilter\"\u003eZerofilter\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eExterior dimensions are mostly preserved from the original. BOM (including the iRobot Roomba 800\/900 series vacuum filter) is very similar, except for:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e4x M3x8 FHCS are now needed (8mm length instead of 6mm) \u003c\/li\u003e\n\u003cli\u003e2x M3x6 BHCS + 2x M3 nuts (optional)\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eIn order for the lever arm to open fully and eject the filter without colliding with the top-hat hinge, the exhaust must be mounted (a) at the back right of the top-hat in its original orientation or (b) at the back left in a 180-degree-rotated orientation.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eThe latter is my preference and what I have referred to as the Standard option in the organization of the files. The back left position is compatible with an adjusted version of the \u003ca target=\"_blank\" rel=\"noopener noreferrer ugc\" href=\"https:\/\/www.printables.com\/model\/408745-v0-upper-rear-bowden-inlet-urbi-for-voron-v0\"\u003eURBI mod from Maple Leaf Makers\u003c\/a\u003e. I don't have a CAD file for the URBI-SFS2, but I have included the modified STL file that I patched together in 3D Builder (the SFS2 mount and PTFE pass-through hole have both been shifted over by 16mm and a notch has been added for fan wire routing).\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eIn either case, the fan lid component needed to be shortened to allow the top-hat to open to 90 degrees. \u003c\/p\u003e\u003ch4\u003e\u003cstrong\u003ePrinted Parts\u003c\/strong\u003e\u003c\/h4\u003e\u003cp\u003eChoose standard or alternate orientation according to PTFE tube routing on your printer. Print 1x each of the following in ABS\/ASA.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMounting Panel\u003c\/li\u003e\n\u003cli\u003eFilter Inlet Duct\u003c\/li\u003e\n\u003cli\u003eFilter Housing\u003c\/li\u003e\n\u003cli\u003eFilter Lever\u003c\/li\u003e\n\u003cli\u003eFan Duct\u003c\/li\u003e\n\u003cli\u003eFan Lid\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eVoron PIF spec (4 perimeters, 5 top\/bottom layers, 40% infill) is recommended for the mounting panel. The other parts need not be so sturdy.\u003c\/p\u003e\u003ch4\u003e\u003cstrong\u003eAssembly \u003c\/strong\u003e\u003c\/h4\u003e\u003col\u003e\n\u003cli\u003eFollow steps #2-8 from the original model.\u003c\/li\u003e\n\u003cli\u003eRemove acrylic panel from the back of the top-hat.\u003c\/li\u003e\n\u003cli\u003eApply 5mm x 1mm foam tape to the printed panel.\u003cbr\u003e\u003cimg class=\"image_resized\" style=\"width: 337px\" src=\"https:\/\/makerworld.bblmw.com\/makerworld\/model\/DSM00000001325257\/design\/8d5ffcbb-e651-44f3-8ba1-da2b5392316b.webp\"\u003e\u003cimg class=\"image_resized\" style=\"width: 337px\" src=\"https:\/\/makerworld.bblmw.com\/makerworld\/model\/DSM00000001325257\/design\/bb5ba3f2-748d-4ca5-adf6-1f9ad838b5e1.webp\"\u003e\n\u003c\/li\u003e\n\u003cli\u003eInstall the replacement panel behind the original clips and hinges.\u003c\/li\u003e\n\u003cli\u003e(Optional) since the printed panel is not as stiff as the acrylic, adding a couple of M3x6 BHCS through the tabs at the top can help to seal the panel to the frame. This does require adding a couple of M3 nuts, either by using 1515-compatible drop-in nuts or slightly disassembling the top-hat to slide in regular nuts.\u003c\/li\u003e\n\u003cli\u003eAlign the housing with the panel and attach with 4x M3x8 FHCS.\u003c\/li\u003e\n\u003cli\u003eRun the fan wire straight down the back of the printer and into the electronics bay.\u003c\/li\u003e\n\u003cli\u003eConclude with steps #13-16 from the original model.\u003c\/li\u003e\n\u003c\/ol\u003e\u003cp\u003eDesign by cliftoce on MakerWorld (license: BY-SA).\u003c\/p\u003e","brand":"Mymadmanlab","offers":[{"title":"Default Title","offer_id":67391339036976,"sku":null,"price":29.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0987\/0809\/5280\/files\/0_673c6c91-e1e9-4b1b-99a4-86fc7c443a0f.png?v=1784747826","url":"https:\/\/mymadmanlab.com\/products\/5015-blower-hepa-exhaust-for-voron-0-2","provider":"Mymadmanlab.com","version":"1.0","type":"link"}