{"product_id":"calibration-orcaslicer-bambustudio-print-profile","title":"Calibration OrcaSlicer\/BambuStudio print profile","description":"\u003cp\u003e\u003cstrong\u003eI wanted to thank \u003c\/strong\u003e\u003ca target=\"_blank\" rel=\"noopener noreferrer ugc\" href=\"https:\/\/www.printables.com\/@SteveHanov\"\u003e\u003cstrong\u003e@SteveHanov\u003c\/strong\u003e\u003c\/a\u003e\u003cstrong\u003e - this is his brilliant idea for \u003c\/strong\u003e\u003ca target=\"_blank\" rel=\"noopener noreferrer ugc\" href=\"https:\/\/www.printables.com\/model\/293772-dimensional-accuracy-using-linear-equations\"\u003e\u003cstrong\u003ecalibrating prints\u003c\/strong\u003e\u003c\/a\u003e\u003cstrong\u003e, I just tweaked it a bit....\u003c\/strong\u003e\u003cbr\u003eI've corrected a miscalculation and adapted the calibration model to a 5mm diameter drill bit - it's more accurate than a screw head.\u003c\/p\u003e\u003cp\u003e***********************************************************************************************\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat to do with this model?\u003c\/strong\u003e\u003cbr\u003e\u003cstrong\u003eThis is a model for calibrating prints from a specific filament (or rather for calibrating silcer settings) - it is not a printer calibration.\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIn other words, if you need a functional print where dimensional accuracy to the model is important, then this calibration is for you.\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThis calibration allows you to calculate:\u003cbr\u003e- the shrinkage value of the felt,\u003cbr\u003e- x-y correction,\u003cbr\u003e- hole correction.\u003c\/p\u003e\u003cp\u003ePersonally, I use Oracaslicer (BambuStudio has the same parameters available) there all three values are included in the parameters:\u003cbr\u003eThe shrinkage value in the parameters of the filament.\u003cbr\u003eThe x-y correction and hole correction in the print parameters.\u003c\/p\u003e\u003cp\u003e-----------------------------------------------------------------------------------------------------------\u003c\/p\u003e\u003cp\u003eOn the model, the -4 and +4 mark the values of the extreme holes:\u003cbr\u003e-4 o means 4.6 mm (i.e. -0.4 mm from the diameter of the reference hole)\u003cbr\u003e+4 means 5.4 mm (i.e. +0.4 mm from the reference hole diameter)\u003c\/p\u003e\u003cp\u003eSo:\u003cbr\u003e- if the drill enters the holes in the +4 direction when measuring - the values are subtracted.\u003cbr\u003e- if the drill enters the holes in the -4 direction when measuring - the values are added.\u003c\/p\u003e\u003cfigure class=\"image\"\u003e\u003cimg src=\"https:\/\/makerworld.bblmw.com\/makerworld\/model\/DSM00000001291942\/design\/2025-01-28_xf0b7d3zrion.png\"\u003e\u003c\/figure\u003e\u003cp\u003e----------------------------------------------------------------------------------------------------------\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow it works:\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e\u003cbr\u003e\u003cstrong\u003e1. Print the model.\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e2. Open \u003c\/strong\u003e\u003ca target=\"_blank\" rel=\"noopener noreferrer ugc\" href=\"https:\/\/www.wolframalpha.com\/input?i=systems+of+equations+calculator\u0026amp;assumption=%7B%22F%22%2C+%22SolveSystemOf3EquationsCalculator%22%2C+%22equation1%22%7D+-%3E%22100a+-+2b+%3D+99.32%22\u0026amp;assumption=%22FSelect%22+-%3E+%7B%7B%22SolveSystemOf3EquationsCalculator%22%7D%2C+%22dflt%22%7D\u0026amp;assumption=%7B%22F%22%2C+%22SolveSystemOf3EquationsCalculator%22%2C+%22equation2%22%7D+-%3E%2210a+-+2b%3D9.88%22\u0026amp;assumption=%7B%22F%22%2C+%22SolveSystemOf3EquationsCalculator%22%2C+%22equation3%22%7D+-%3E%225%2Fa+-+2c+%3D+4.9%22\"\u003e\u003cstrong\u003elink with calculations for our model\u003c\/strong\u003e\u003c\/a\u003e\u003cstrong\u003e.\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e\u003cimg src=\"https:\/\/makerworld.bblmw.com\/makerworld\/model\/DSM00000001291942\/design\/2025-01-28_lf25zjv7wags.png\"\u003e\u003cbr\u003e\u003cstrong\u003e3. Measure the longer side and enter the result in the calculation area: ‘99.32’.\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e\u003cbr\u003e\u003cstrong\u003e4. Measure the shorter side and enter the result in the calculation area: ‘9.88’.\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e\u003cbr\u003e\u003cstrong\u003e5. Insert the 5mm drill bit into the smallest hole it will fit into:\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e\u003cbr\u003e     The middle hole is the reference hole and is assumed to be the zero hole. \u003c\/p\u003e\u003cp\u003e     \u003c\/p\u003e\u003cp\u003e\u003ci\u003eExample1\u003c\/i\u003e                                                                ===\u003cbr\u003e     For example, if you place a 5mm drill three holes higher than the center hole (in the +4 direction), enter a value of 4.7 in the \"4.9\" calculation point. \u003cbr\u003e     The holes differ by 0.1 mm, so the reference hole is 4.7 mm because you only put the drill into the third hole.\u003c\/p\u003e\u003cp\u003e     Drill+0.3mm=5mm\u003cbr\u003e     Drill=5-0.3=4.7\u003c\/p\u003e\u003cfigure class=\"image\"\u003e\u003cimg src=\"https:\/\/makerworld.bblmw.com\/makerworld\/model\/DSM00000001291942\/design\/2025-01-28_cvkovsfjzcvc.png\"\u003e\u003c\/figure\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e\u003ci\u003eExample2 \u003c\/i\u003e                                                               ===\u003cbr\u003e     For example, if you put the drill into 1 hole above the reference hole, you should enter in \u003cbr\u003e4.9 in the place of ‘4.9’.\u003c\/p\u003e\u003cp\u003e     Drill+0.1mm=5mm\u003cbr\u003e     Drill=5-0.1=4.9\u003c\/p\u003e\u003cfigure class=\"image\"\u003e\u003cimg src=\"https:\/\/makerworld.bblmw.com\/makerworld\/model\/DSM00000001291942\/design\/2025-01-28_2k066ado4tc1.png\"\u003e\u003c\/figure\u003e\u003cp\u003e\u003cbr\u003e \u003c\/p\u003e\u003cp\u003e\u003ci\u003eExample3 \u003c\/i\u003e                                                               ===\u003c\/p\u003e\u003cp\u003e     For example, if the drill has already entered the second hole, but in a direction of -4 from the centre hole, a value of 5.2 should be entered into the calculation instead of \"4.9\".\u003c\/p\u003e\u003cp\u003e     Drill-0.2mm=5mm\u003cbr\u003e     Drill=5+0.2=5.2\u003c\/p\u003e\u003cfigure class=\"image\"\u003e\u003cimg src=\"https:\/\/makerworld.bblmw.com\/makerworld\/model\/DSM00000001291942\/design\/2025-01-28_kavjbyjtsvnv.png\"\u003e\u003c\/figure\u003e\u003cp\u003e     \u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e6. Once the measured values have been entered:\u003c\/strong\u003e\u003cbr\u003e\u003cstrong\u003e     1) Switch on \"Compute\".\u003c\/strong\u003e\u003cbr\u003e\u003cstrong\u003e     2) Then \"Approximate form\".\u003c\/strong\u003e\u003c\/p\u003e\u003cfigure class=\"image\"\u003e\u003cimg src=\"https:\/\/makerworld.bblmw.com\/makerworld\/model\/DSM00000001291942\/design\/2025-01-28_sus9oznqy30b.jpg\"\u003e\u003c\/figure\u003e\u003cp\u003eWe have now received the results in a form that we can already enter in Oracslicer.\u003c\/p\u003e\u003cfigure class=\"image\"\u003e\u003cimg src=\"https:\/\/makerworld.bblmw.com\/makerworld\/model\/DSM00000001291942\/design\/2025-01-28_b2plq2qdibtf.jpg\"\u003e\u003c\/figure\u003e\u003cp\u003e\u003cstrong\u003e7. After the measurements and calculations, the results for the values a, b, c are entered in Orcaslicer\/BambuStudio respectively:\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e- the shrinkage value of the filament - the ‘a’ value of the calculation results multiplied by 100.\u003cbr\u003eFor example if a≈0.993778 then the shrinkage value will be: 99,3778 %\u003c\/p\u003e\u003cfigure class=\"image\"\u003e\u003cimg src=\"https:\/\/makerworld.bblmw.com\/makerworld\/model\/DSM00000001291942\/design\/2025-01-28_2tws3e76kn2m.jpg\"\u003e\u003c\/figure\u003e\u003cp\u003e\u003cbr\u003e- x-y correction - value ‘b’ of the calculation results.\u003cbr\u003e- hole correction - value ‘c’ of the calculation results.\u003c\/p\u003e\u003cfigure class=\"image\"\u003e\u003cimg src=\"https:\/\/makerworld.bblmw.com\/makerworld\/model\/DSM00000001291942\/design\/2025-01-28_7pnkvo5g8nk1.jpg\"\u003e\u003c\/figure\u003e\u003cp\u003eIn other slicers these parameters may be described differently in not all may be hole correction.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e8. Having entered the above parameters into Orcaslicer\/BambuStudio for our filament, we can print the calibration model again.\u003c\/strong\u003e\u003cbr\u003e\u003cstrong\u003eA well calibrated model should be 100x10x5mm and the 5mm drill should fit tightly into the centre hole.\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e***********************************************************************************************\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cfigure class=\"table\"\u003e\u003ctable style=\"border: 5px solid #65C900\"\u003e\u003ctbody\u003e\u003ctr\u003e\u003ctd style=\"border: 2px solid #65C900\"\u003e\n\u003cp\u003eCONCLUSION\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e💚💚💚If you enjoyed the project please like it.💚💚💚\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePost your makes and let me know how it works out for you. \u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eIf anyone has any comments about them - I'd be happy to listen and improve the models.\u003c\/p\u003e\n\u003c\/td\u003e\u003c\/tr\u003e\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/figure\u003e\u003cp\u003eDesign by Mario_L on MakerWorld (license: BY-ND).\u003c\/p\u003e","brand":"Mymadmanlab","offers":[{"title":"Default Title","offer_id":67448689623344,"sku":null,"price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0987\/0809\/5280\/files\/0_fe65a726-52bd-435f-a9f7-9d192c514f7e.jpg?v=1785819854","url":"https:\/\/mymadmanlab.com\/products\/calibration-orcaslicer-bambustudio-print-profile","provider":"Mymadmanlab.com","version":"1.0","type":"link"}