{"product_id":"car-door-trash-bin","title":"Car Door Trash Bin","description":"\u003cp\u003eSmall trash bin to install in any door of any car.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003ch3\u003eBefore you start choose the correct size for your car\u003c\/h3\u003e\u003cp\u003eYou need to measure the space available on your car door to install the trash bin and choose the size that best suits you. \u003cstrong\u003eIsn't the size you need available? Let me know and I'll be happy to add it!\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eDid you know that I have another trash can to install in the can holder of your car? \u003ca target=\"_blank\" rel=\"noopener noreferrer ugc\" href=\"https:\/\/www.prusaprinters.org\/prints\/136766-car-door-trash-can\"\u003eCheck it out\u003c\/a\u003e!\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003ch3\u003eNecessary materials\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e2x m3 nuts.\u003c\/li\u003e\n\u003cli\u003e2x m3 x 30mm screws.\u003c\/li\u003e\n\u003cli\u003eSmall bags, \u003ca target=\"_blank\" rel=\"noopener noreferrer ugc\" href=\"https:\/\/amzn.to\/3HPl6Ll\"\u003esuch as these for dog poops 💩\u003c\/a\u003e.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e \u003c\/p\u003e\u003ch3\u003ePrinting instructions\u003c\/h3\u003e\u003cp\u003eYou need to print 1 Lid, 1 Bin and 1 Holder of the right size for your car, make sure \u003cstrong\u003eall 3 parts are named with the same size\u003c\/strong\u003e.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eAll parts are already oriented to be able to be printed without supports\u003c\/strong\u003e.\u003cstrong\u003e \u003c\/strong\u003eThere are some bridges but they are in non-visible areas.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003ePLA is not a suitable material for this model\u003c\/strong\u003e since cars reach sufficient temperatures for it to melt, \u003cstrong\u003eI personally recommend using PETG\u003c\/strong\u003e since it is very easy to print and will more than withstand these temperatures, but you can also use other more resistant materials like ABS or ASA. It is recommended that the holder material has some flexibility, the other parts can be completely rigid.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003ch3\u003eAssembly instructions\u003c\/h3\u003e\u003col\u003e\n\u003cli\u003eFirst insert the two nuts into their holes in the lid.\u003c\/li\u003e\n\u003cli\u003eNow put the lid and the bin together and proceed to hold them with the screws, do not tighten the screws too much to allow the movement of the lid.\u003c\/li\u003e\n\u003cli\u003eInsert the bag through the hole of the holder, make sure the opening of the bag is on the side where the holder clips are.\u003c\/li\u003e\n\u003cli\u003eFold the edge of the bag over so that it wraps around the holder.\u003c\/li\u003e\n\u003cli\u003eInsert the holder through the bottom of the bin until the clips hold it in place, the edges of the bag should stay clamped between the holder and the bin.\u003c\/li\u003e\n\u003cli\u003eNow all you have to do is install the bin on the door of your car.\u003c\/li\u003e\n\u003c\/ol\u003e\u003cp\u003e \u003c\/p\u003e\u003ch3\u003eChanging the bag\u003c\/h3\u003e\u003col\u003e\n\u003cli\u003eRemove the trash bin from your car door.\u003c\/li\u003e\n\u003cli\u003eSqueeze the holder in the center until you can pull it out of the bin from the bottom.\u003c\/li\u003e\n\u003cli\u003eRemove your bag and replace it with a new one the same way you did in steps 4-6 of the assembly instructions.\u003c\/li\u003e\n\u003c\/ol\u003e\u003cp\u003e \u003c\/p\u003e\u003ch3\u003e\u003cstrong\u003eFAQ:\u003c\/strong\u003e\u003c\/h3\u003e\u003cp\u003eWhy does the hinge require screws instead of a fully 3D-printed solution?\u003c\/p\u003e\u003cp\u003eOriginally, the hinge was entirely 3D-printed. However, aside from the printing challenges, even when using heat-resistant materials like ABS, the hinges eventually stopped functioning properly or even broke. I believe screws are an accessible solution for everyone, and so far, my longest-running test (since February 2024) is still holding up well.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eThe available sizes don’t fit my car. How can I get one that does?\u003c\/p\u003e\u003cp\u003eSimply request it in the comments section. The design is fully parametric, so I can adjust it to the required size. Just let me know your car’s dimensions (I will always round down slightly to ensure a proper fit), and within a few days, I’ll upload the size you need.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eI found a flaw in the design, I'm having trouble printing it, or I think it could be improved…\u003c\/p\u003e\u003cp\u003eThis is the third iteration of this design (and likely the last), as I’ve been using it for several years without finding any major issues. However, if you have any ideas or encounter problems with the model, let me know, and I’ll consider whether it’s worth designing a new version.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan I share, modify, sell, etc., this design?\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe license indicated on the website is CC-BY, which means you can do pretty much anything you want with it as long as you give credit to me as the designer. A link to the design’s page or my Makerworld profile is more than enough in most cases.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eI love your design, or I'm selling it and would like to thank you in some way\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eBesides sharing your make and leaving a comment, I also accept donations via PayPal—you can find the link on my Makerworld profile. I truly appreciate all the support; it motivates me to keep publishing new designs.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eDesign by Katarn on MakerWorld (license: BY).\u003c\/p\u003e","brand":"Mymadmanlab","offers":[{"title":"Default Title","offer_id":67383332471088,"sku":null,"price":7.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0987\/0809\/5280\/files\/0_02189c69-4e90-4c60-bac2-bc1cdd49d3da.png?v=1784500816","url":"https:\/\/mymadmanlab.com\/products\/car-door-trash-bin","provider":"Mymadmanlab.com","version":"1.0","type":"link"}