{"product_id":"christmas-tree-ornament-110-x-47mm-nonagonal-9-sided","title":"Christmas Tree Ornament 110 x 47mm (Nonagonal - 9 sided)","description":"\u003cp\u003eThis is the goldilocks ornament, not too big, not too small, but just right. It is 9-sided or Nonagonal, so looks really nice.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eIt is 110 mm from the very top of to the bottom, and about 47mm at the widest point.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eI found many ornaments to be too large for the smaller UK Christmas trees, houses smaller, so trees smaller. Of course, you can scale it up by any percentage you like for much larger. I would be careful going smaller, as the top will get very thin.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e\u003ci\u003eRemember at 200% scale you are at 200mm hight, so check your printer volume before printing. The end cap is a separate print.\u003c\/i\u003e\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eIf you need hooks for the ornament, then these were designed to work with it. \u003ca target=\"_blank\" href=\"https:\/\/makerworld.com\/en\/models\/218969\" rel=\"nofollow noopener\"\u003ehttps:\/\/makerworld.com\/en\/models\/218969\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003e\u003cstrong\u003eMaterial\u003c\/strong\u003e\u003c\/h3\u003e\u003cp\u003eI have used two colour PLA and that looks nice (blue and red, gold and silver), I have also used single colour (dark yellow) and they have all turned out fantastically.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eUse your most decorative filament, the fancier the better. I used PLA, but anything nice will work well.\u003c\/p\u003e\u003ch3\u003e\u003cstrong\u003ePrinting\u003c\/strong\u003e\u003c\/h3\u003e\u003cp\u003eUse vase\/spiral mode.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eNo supports needed\u003c\/li\u003e\n\u003cli\u003eNo brim needed\u003c\/li\u003e\n\u003cli\u003e0.4mm nozzle\u003c\/li\u003e\n\u003cli\u003e0.5mm layer width\u003c\/li\u003e\n\u003cli\u003e0.2mm layer height\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eIt has a small base, but I have had no trouble with it staying put. Removal should be straightforward.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003ePrint the ornament with the top (where the top is glued on) to the bed and let the ornament spiral upwards - towards what will be the bottom.\u003c\/p\u003e\u003cp\u003ePrint the top, with the eye for the hook or cotton to the top, with the flat base at the bottom.\u003c\/p\u003e\u003ch3\u003e\u003cstrong\u003eAssembly\u003c\/strong\u003e\u003c\/h3\u003e\u003cp\u003eA dab of superglue on the top, then carefully hold in place. I use superglue, but the one you like should work with the type of plastic you use.\u003c\/p\u003e\u003ch3\u003e\u003cstrong\u003eNote\u003c\/strong\u003e\u003c\/h3\u003e\u003cp\u003eThis is printed in vase\/spiral mode, so the walls are comparatively thin. this means that if you push too hard on the sides, it will break. So, treat it gently and it will last for years.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eIf you get little blobs on your print, it might be due to the Power Out system that saves the state to the SD card periodically. I have it turned off, but it does happen with many short curves, like this has.\u003c\/p\u003e\u003ch3\u003e\u003cstrong\u003eFinishing Ideas\u003c\/strong\u003e\u003c\/h3\u003e\u003cp\u003eI have not tried this yet, but am planning on doing so:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eSpray snow to put a light dusting on the top, so it looks like snow fell onto the ornament\u003c\/li\u003e\n\u003cli\u003eA little glue and some glitter to jazz up a single colour - to match your tree\u003c\/li\u003e\n\u003cli\u003eFor the children, draw their own designs to make them personal - for this year and the next few.\u003c\/li\u003e\n\u003cli\u003eSome spray on glitter, like used for hair is another option.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eDesign by Katie on MakerWorld (license: BY-SA).\u003c\/p\u003e","brand":"Mymadmanlab","offers":[{"title":"Default Title","offer_id":67408815128880,"sku":null,"price":4.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0987\/0809\/5280\/files\/0_9a5c8353-7eb9-464e-a983-3493b51c9a23.png?v=1785229970","url":"https:\/\/mymadmanlab.com\/products\/christmas-tree-ornament-110-x-47mm-nonagonal-9-sided","provider":"Mymadmanlab.com","version":"1.0","type":"link"}