{"product_id":"containers-in-vase-or-spiral-mode-openscad-customizable-fast-and-cheap","title":"Containers in Vase- or Spiral-mode. OpenScad, Customizable, Fast and Cheap","description":"\u003ch2\u003eSummary\u003c\/h2\u003e\u003cp\u003eFully Customizable containers to be printed in Vase- or spiral-mode. To create your own boxes you need the free program Openscad (see below).\u003cbr\u003eThe Spiral-mode makes it cheap and fast to print. Minimum material, no seams, most of the times great quality.\u003cbr\u003eYou can use it for ordinary storing-boxes, creditcard-cases, case for calculators, a cigarette box for your wooden cigarettes etc.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e\u003ci\u003e\u003cstrong\u003eLimitations:\u003c\/strong\u003e\u003c\/i\u003e\u003cbr\u003eThe spiral mode makes it cheap but also limited. Because the walls are only one layer thick, it is less suitable for bigger boxes. The useable size depends on the nozzle-width you are using. Smaller nozzle-width gives a weaker result then bigger widths. I myself use 0.6, which gives me reasonable results at 13cm a side. And fairly strong boxes below 10cm a side. For 0.4 stay beneath the 10 cm a side. Of course it also depends on the purpose of the box.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e\u003ci\u003e\u003cstrong\u003eCustomizer:\u003c\/strong\u003e\u003c\/i\u003e\u003cbr\u003eYou can use the .scad-file in the free program Openscad directly (link below) to create boxes as you like. Instructions how it works by Dr Lex: \u003ca target=\"_blank\" href=\"https:\/\/www.dr-lex.be\/3d-printing\/customizer.html\" rel=\"nofollow noopener\"\u003ehttps:\/\/www.dr-lex.be\/3d-printing\/customizer.html\u003c\/a\u003e. \u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e\u003ci\u003e\u003cstrong\u003eThe not so obvious parameters:\u003c\/strong\u003e\u003c\/i\u003e\u003cbr\u003e-\u003cstrong\u003etol\u003c\/strong\u003e(erance): this will give the room between the lid and the box. If it is too big, the lid will go off to easily. If it is too tight, the lid is hard to fit, and the sides will bend inward. Default it is set to 0.15, which gave the best results on my printers. Loose enough to take the lid of easily, tight enough to pick it up filled with screws without loosing the box.\u003c\/p\u003e\u003cp\u003e-\u003cstrong\u003enpan1 and 2\u003c\/strong\u003e: gives the number of \"panels\" at a side. Panels will give you some more rigidity. The size of the panels is calculated by the script. If the number given is bigger than the number that will fit, it recalculates the number of panels.\u003c\/p\u003e\u003cp\u003e-\u003cstrong\u003eoutput\u003c\/strong\u003e: give you the opportunity to only export the lid or the box. Default it will export both in the same STL.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e\u003ci\u003e\u003cstrong\u003eVase- or Spiral-mode:\u003c\/strong\u003e\u003c\/i\u003e\u003cbr\u003eWhen you are looking at the example Stl's and the results in the customizer, the boxes and lids are not hollow but solid. This is a requirement for spiral-mode. The slicer-software will transform it to a box if you select the spiral mode in your slicer (result in the preview-section of the slicer-software)\u003cbr\u003eIf you are not familiar with this function in your slicer, it basically lays a bottom (setting: 2 or 3 layers are fine) and from there it spiralizes in one go upwards to the top of the print. So no layer changes and no seams. Because of that it is fast and gives nice results.\u003cbr\u003eIn Slic3r, PrusaSlicer and Bambu Studio it is called \"Spiral vase\", in Cura it is called \"Spiralize outer contour\".\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e\u003ci\u003e\u003cstrong\u003ePrepare your model in the Slicer:\u003c\/strong\u003e\u003c\/i\u003e\u003cbr\u003eAs you can see the default output of the customizer is a box and a lid (you can change that with the output-parameter). If you want to print them at the same time (not necessary) you first have to split the model into its two parts. Menu command \"Split\" in Slic3r, \"Split to Parts\" in Bambu Studio and Prusaslicer and in Cura you have to download the extension \"Meshtools\" from the marketplace to make it possible (afaik).\u003cbr\u003eBecause it is supposed to print in Spiral\/Vase-mode, you can't jump each layer from the box to the lid and back. So you have to print them in sequence\/by object. In Slic3r and Prusaslicer you can find it under \"print-settings \u0026gt; output options \u0026gt; Complete individual objects\", in Cura “Special modes \u0026gt; Print sequence” and in Bambu Studio in “Others” \u0026gt; “Print sequence” \u0026gt; “By object”\u003c\/p\u003e\u003cp\u003eTo be safe, place the two parts each in an opposite corner to avoid collision with the printhead if the first part is printed. It usually prints the lowest part (lid) first, so the danger is small. More information about this function: \u003ca target=\"_blank\" href=\"https:\/\/www.youtube.com\/watch?v=u4YONDL4iXo\" rel=\"nofollow noopener\"\u003ehttps:\/\/www.youtube.com\/watch?v=u4YONDL4iXo\u003c\/a\u003e (Chep)\u003cbr\u003eWhen you have some experience with it, you can print more boxes at the same run if your bed is big enough.\u003c\/p\u003e\u003cp\u003eIf you made it this far,\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eHappy Boxing :)\u003cbr\u003e \u003c\/p\u003e\u003cp\u003eMore information about the fantastic and challenging program OpenSCAD can be found here: \u003ca target=\"_blank\" href=\"https:\/\/en.wikibooks.org\/wiki\/OpenSCAD_User_Manual\" rel=\"nofollow noopener\"\u003ehttps:\/\/en.wikibooks.org\/wiki\/OpenSCAD_User_Manual\u003c\/a\u003e\u003c\/p\u003e\u003cp\u003eYou can download the free and opensource OpenSCAD here:\u003cbr\u003e\u003ca target=\"_blank\" href=\"http:\/\/www.openscad.org\/downloads.html\" rel=\"nofollow noopener\"\u003ehttp:\/\/www.openscad.org\/downloads.html\u003c\/a\u003e\u003cbr\u003eYou can also try a webbrowser version without installing anything like: \u003ca target=\"_blank\" href=\"https:\/\/openscad.cloud\/openscad\/\" rel=\"nofollow noopener\"\u003ehttps:\/\/openscad.cloud\/openscad\/\u003c\/a\u003e copy the code in the scadfile and paste the code at the left side.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003ch2\u003ePrint Settings\u003c\/h2\u003e\u003cp\u003e\u003cstrong\u003eRafts: \u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eNo\u003c\/p\u003e\u003cp\u003e                                            \u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSupports: \u003c\/strong\u003e                    \u003c\/p\u003e\u003cp\u003eNo\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eDesign by Coat Over on MakerWorld (license: BY).\u003c\/p\u003e","brand":"Mymadmanlab","offers":[{"title":"Default Title","offer_id":67400429273392,"sku":null,"price":4.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0987\/0809\/5280\/files\/0_2597714a-f98e-469f-8016-4129d39b33da.jpg?v=1784943687","url":"https:\/\/mymadmanlab.com\/products\/containers-in-vase-or-spiral-mode-openscad-customizable-fast-and-cheap","provider":"Mymadmanlab.com","version":"1.0","type":"link"}