{"product_id":"frozen-ice-shards-lamp-for-led-kit-001-vase-mode","title":"Frozen Ice Shards Lamp for LED Kit 001 (vase mode)","description":"\u003ch2\u003eFrosted Ice Shards Lamp\u003c\/h2\u003e\u003cp\u003e\u003ci\u003e\u003cstrong\u003efor Bambu Labs LED Lamp Kit 001 - looking great during both day and when lit at night\u003c\/strong\u003e\u003c\/i\u003e\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e------------------------------------------------------\u003c\/p\u003e\u003ch3\u003e\u003ci\u003eIMPORTANT! READ THESE INFORMATIONS BEFORE PRINTING!\u003c\/i\u003e\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eUse transparent PETG for the lamp shade, rather than transparent PLA\u003cul\u003e\n\u003cli\u003eAll PETG filaments MUST be dried before use, for best results. After you open the plastic packaging, dry the PETG for 4-6 hours at 60-65 ºC. \u003c\/li\u003e\n\u003cli\u003eI have tried multiple transparent PLA and PETG filaments and done a host of tests on each type, and the difference is very visible when both are at their best: Transparent PETG wins big time in transparency. Transparent PLA becomes a muddy translucent at best.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cli\u003eFor transparent PETG, use the following settings, but beware these values may vary slightly with the filament you have:\u003cul\u003e\n\u003cli\u003eFlow ratio: 1.03\u003cul\u003e\u003cli\u003eThis ensures a better layer adhesion and more invisible layers, with better transparency as the layer gaps are filled out. Some over extrusion may occur, but it should not be overly much.\u003c\/li\u003e\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cli\u003ePrint at 255 ºC or whatever is the highest your filament is rated for.\u003c\/li\u003e\n\u003cli\u003eMax volumetric speed at 10 mm3\/s or lower.\u003c\/li\u003e\n\u003cli\u003eIn the “COOLING” tab, set the Part Cooling's Max Fan speed treshold to 10%\u003cul\u003e\u003cli\u003eAny cooling fan will make the PETG lose its transparency gradually, but the problem is more evident at fan speeds over 15%. We need to be able to print overhangs that don't droop, so keeping it at 10% is a good compromize.\u003c\/li\u003e\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cli\u003eAlso in the \"COOLING\" tag, set Auxiliary Fan speed to 0%.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e------------------------------------------\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFOR PEOPLE WHO DO NOT USE A BAMBU LABS PRINTER:\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eI have provided STL files\u003c\/p\u003e\u003cp\u003eWhile you can slice the base pretty much as you like, I recommend the following for the faceted crystal lamp shade:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eEnable “Spiral Vase” or “Vase mode” (in some slicers, this is called “Spiralize outer contour”).\u003c\/li\u003e\n\u003cli\u003eChoose a large layer height at 0.28mm.\u003cul\u003e\u003cli\u003eThis is to create fewer layer lines. A more coarse z-resolution is not a drawback for this print.\u003c\/li\u003e\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cli\u003eSet outer wall to at least 0.6mm width.\u003cul\u003e\u003cli\u003eThis value is for 0.4mm nozzles. Depending on your nozzle's base, some 0.4mm nozzles can go as high as 0.8mm. However, 0.6mm layer width is the most that all 0.4mm nozzles can go, so consider this a “safe value”. This is to ensure sturdiness.\u003c\/li\u003e\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cli\u003eUse 3 bottom layers.\u003c\/li\u003e\n\u003cli\u003eSpeed for outer wall at max 20 mm\/s and acceleration at maximum 7000 mm\/s^2\u003cul\u003e\u003cli\u003eFaster speeds will cause the transparency to gradually become more milky and translucent.\u003c\/li\u003e\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e------------------------------------------------------\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDISCLAIMER!\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eThis is a remix of Crincle Lamp by LoboCNC:\u003c\/p\u003e\u003cp\u003e\u003ca target=\"_blank\" href=\"https:\/\/makerworld.com\/en\/models\/95238\" rel=\"nofollow noopener\"\u003eCrinkle Lamp by LoboCNC - MakerWorld\u003c\/a\u003e\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eHis Crincle Lamp is in turn also a remix - of Voronoi Lamp by Markellov:\u003c\/p\u003e\u003cp\u003e\u003ca target=\"_blank\" href=\"https:\/\/www.thingiverse.com\/thing:584714\" rel=\"nofollow noopener\"\u003eVoronoi lamp by Markellov - Thingiverse\u003c\/a\u003e\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eI sized the lamp down, added some top and bottom and made some minor corrections - and a base to fit the LED Kit 001 as well as keep the lamp shade in place. \u003c\/p\u003e\u003cp\u003eDesign by jakobdam on MakerWorld (license: BY).\u003c\/p\u003e","brand":"Mymadmanlab","offers":[{"title":"Default Title","offer_id":67367867744560,"sku":null,"price":9.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0987\/0809\/5280\/files\/0_db0383c0-88e8-4634-9757-1316c8b8df2d.png?v=1784017928","url":"https:\/\/mymadmanlab.com\/products\/frozen-ice-shards-lamp-for-led-kit-001-vase-mode","provider":"Mymadmanlab.com","version":"1.0","type":"link"}