{"product_id":"functioning-switchblade","title":"Functioning Switchblade","description":"\u003cp\u003eASSEMBLY: \u003c\/p\u003e\u003cp\u003e    (VIDEO found at bottom)\u003c\/p\u003e\u003cp\u003e    Attach both \u003cstrong\u003e\u003cu\u003eSprings\u003c\/u\u003e\u003c\/strong\u003e into the \u003cstrong\u003e\u003cu\u003eBottom Case\u003c\/u\u003e\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e    Place \u003cstrong\u003e\u003cu\u003eRubber Band\/s\u003c\/u\u003e\u003c\/strong\u003e around the \u003cstrong\u003e\u003cu\u003eSlider\u003c\/u\u003e\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e    Place The \u003cstrong\u003e\u003cu\u003eBlade\u003c\/u\u003e\u003c\/strong\u003e with the middle in the centre of the \u003cstrong\u003e\u003cu\u003eSprings\u003c\/u\u003e \u003c\/strong\u003eso it sticks slightly out\u003c\/p\u003e\u003cp\u003e    Place The \u003cstrong\u003e\u003cu\u003eSlider\u003c\/u\u003e\u003c\/strong\u003e on top of the \u003cstrong\u003e\u003cu\u003eSprings\u003c\/u\u003e \u003c\/strong\u003emaking sure the springs separate when pushed forward\/back\u003c\/p\u003e\u003cp\u003e    Place The \u003cstrong\u003e\u003cu\u003eTop Case\u003c\/u\u003e\u003c\/strong\u003e on the bottom case and click it in\u003c\/p\u003e\u003cp\u003e    Push the \u003cstrong\u003e\u003cu\u003eButton\u003c\/u\u003e \u003c\/strong\u003eover the protruding piece from the \u003cstrong\u003e\u003cu\u003eTop Case\u003c\/u\u003e\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e2023 (V2 (Use) FILES UPLOADED):\u003cbr\u003eI looked back on this project and how Francis_MK3S remixed it to make it even better, I printed the files and realised it only worked after heavy modification so I made my own again, this time its near perfect. The button is tall enough so it cannot interfere with the slider and the blade, the case top slider gap was extended, the slider feet were cut down more, the blade rubber band latch was shortened so it would not be touched by the slider, Finally I added a \"Hellhound blade\" with the correctly sized latch to the rest of the files if you would rather use that. However for this to work you must print the blade \u0026amp; the springs without any elephants foot whatsoever. You could use a raft as this will mostly fix it.\u003c\/p\u003e\u003cp\u003eRemixed from: \u003ca target=\"_blank\" rel=\"noopener noreferrer ugc\" href=\"https:\/\/www.thingiverse.com\/thing:4394741\"\u003ehttps:\/\/www.thingiverse.com\/thing:4394741\u003c\/a\u003e\u003c\/p\u003e\u003cp\u003ethe original barely worked and you had to file loads of it down. With this remix you can print all the parts with a very high success rate and not have to do any post-processing apart from assembly.\u003c\/p\u003e\u003cp\u003e(assembly video on original thing: \u003ca target=\"_blank\" rel=\"noopener noreferrer ugc\" href=\"https:\/\/www.thingiverse.com\/thing:4394741\"\u003ehttps:\/\/www.thingiverse.com\/thing:4394741\u003c\/a\u003e ) however I recommend 2 loombands or ones at that size\u003c\/p\u003e\u003cp\u003ePETG works the best, but you can print all of the following parts in PLA successfully:\u003c\/p\u003e\u003cp\u003e. Top case\u003cbr\u003e. Bottom case\u003cbr\u003e. Blade\u003cbr\u003e. Button\u003c\/p\u003e\u003cp\u003eIt works better if you print these parts in PETG:\u003c\/p\u003e\u003cp\u003e. Slider\u003cbr\u003e. Springs\u003c\/p\u003e\u003cp\u003eAll parts explained:\u003c\/p\u003e\u003cp\u003e. Case2: the case on the bottom that houses the blade, slider, springs and top case\u003c\/p\u003e\u003cp\u003e. Casetop2: top half of the case, goes in-between the button and slider\u003c\/p\u003e\u003cp\u003e. Slider: holds a rubber band and moves the springs apart for the blade\u003c\/p\u003e\u003cp\u003e. Comb blade: the blade but with a comb so its practical\u003c\/p\u003e\u003cp\u003e. Original Blade: pointy blade with sharp edges\u003c\/p\u003e\u003cp\u003e. Springs: both go inside the triangular gaps in the bottom case\u003c\/p\u003e\u003cp\u003e. Button2: goes on the slider above the top case\u003c\/p\u003e\u003cp\u003eParts that may need changes in the slicer:\u003c\/p\u003e\u003cp\u003e. Button - you may need to scale this to ~102% if it doesn't fit well\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e\u003cu\u003eAssembly Video (Not Owned By Me):\u003c\/u\u003e\u003c\/p\u003e\u003cfigure class=\"media\"\u003e\u003coembed url=\"https:\/\/www.youtube.com\/watch?v=i-qvsf0v_p8\"\u003e\u003c\/oembed\u003e\u003c\/figure\u003e\u003cp\u003eDesign by Johny_D06 on MakerWorld (license: BY).\u003c\/p\u003e","brand":"Mymadmanlab","offers":[{"title":"Default Title","offer_id":67383260283184,"sku":null,"price":4.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0987\/0809\/5280\/files\/0_3d98c4de-a3ec-42c5-8b41-8c0a39eb9cd3.png?v=1784494421","url":"https:\/\/mymadmanlab.com\/products\/functioning-switchblade","provider":"Mymadmanlab.com","version":"1.0","type":"link"}