{"product_id":"inside-out-memory-orb-halloween-basket","title":"Inside Out memory orb Halloween basket","description":"\u003cp\u003eWe're doing the Inside Out 2 family theme for Halloween and thought it would be fun to have the kids (and adults) carry around glowing memory orbs corresponding to each character. I tried printing with transparent filament and then colored LEDs but it was more cost effective to print in the color PETG using white LEDs. Plus it looks better in the daytime. The overall glow would look better with a central bright bulb, but then where would the candy go?! Total cost is around $25USD depending on your cost of filament and desired internals. I listed what I used below.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSpecs:\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eThe orb\/sphere is 23cm in diameter. Seemed most proportional for screen-accuracy while still allowing candy to go inside\u003c\/li\u003e\n\u003cli\u003eThe circular handle openings are 21x21mm to use your own handle\u003c\/li\u003e\n\u003cli\u003eThe flat base is nearly 11cm\u003c\/li\u003e\n\u003cli\u003eThe top opening is just over 14cm\u003c\/li\u003e\n\u003cli\u003eUses about 470g of filament\u003c\/li\u003e\n\u003cli\u003eUsing my slow PETG profile, each memory orb takes about 14.5hrs on my P1S\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eFor printing:\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eNo supports needed - overhang is about 73 degrees at the bottom\u003c\/li\u003e\n\u003cli\u003eI used PETG hoping it will hold up when the kids trip and drop these\u003c\/li\u003e\n\u003cli\u003ePrint as pictured (bottom down, opening up). Printing with the opening against the build plate is also possible if your printer handles bridging ok (or you use central supports) but not necessary\u003c\/li\u003e\n\u003cli\u003e3 walls\/perimeters which nearly fills in the ~3mm wall width\u003c\/li\u003e\n\u003cli\u003e15% infill (I'm using crosshatch) should be enough\u003c\/li\u003e\n\u003cli\u003eMy first trial I used part modifiers to do 100% infill around the handle cutouts. This is not necessary and leaves a strange artifact\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSupplies:\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eYour choice of filament. I got this Sunlu PETG bundle for $110: \u003ca target=\"_blank\" href=\"https:\/\/a.co\/d\/5mZUoLA\" rel=\"nofollow noopener\"\u003ehttps:\/\/a.co\/d\/5mZUoLA\u003c\/a\u003e (so about $11\/roll or $5.50 per memory orb)\u003cul\u003e\u003cli\u003eSunlu for orange, pink, blue, yellow, red and green. Using some other purple PETG from Amazon\u003c\/li\u003e\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cli\u003eBattery power for mobile illumination (about $2ea): \u003ca target=\"_blank\" href=\"https:\/\/www.aliexpress.com\/item\/3256806226252799.html\" rel=\"nofollow noopener\"\u003ehttps:\/\/www.aliexpress.com\/item\/3256806226252799.html\u003c\/a\u003e\n\u003c\/li\u003e\n\u003cli\u003eWhite rope LEDs (looked better than just the spaced out lights). About $8.50ea. \u003ca target=\"_blank\" href=\"https:\/\/www.aliexpress.com\/item\/3256807082224473.html\" rel=\"nofollow noopener\"\u003ehttps:\/\/www.aliexpress.com\/item\/3256807082224473.html\u003c\/a\u003e\n\u003c\/li\u003e\n\u003cli\u003e5\/8 inch rope to fit inside the 21mm opening for the handle ($20 for 50ft so about $5\/bucket): \u003ca target=\"_blank\" href=\"https:\/\/a.co\/d\/0Ne90ZY\" rel=\"nofollow noopener\"\u003ehttps:\/\/a.co\/d\/0Ne90ZY\u003c\/a\u003e\u003cul\u003e\u003cli\u003esorry for the freedom units :)\u003c\/li\u003e\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cli\u003eI affixed the LED lights to the inside with packaging tape. This also prevented candy from falling in between the lights. Reflective aluminum tape created dark areas and looked terrible - I would not recommend trying this.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eAlso Included:\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eBesides the OrbBasket.stl (this is what I am printing)….\u003c\/li\u003e\n\u003cli\u003eOrbNoHandleHoles.stl does not have the cutouts so that you can modify or add your own\u003c\/li\u003e\n\u003cli\u003eOrb230mmNoCuts.obj is just the sphere I made from Meshmixer to base everything off of. I couldn't find too many large hollow spheres to suit my needs so I'm sharing this one\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eDesign by maxon on MakerWorld (license: BY).\u003c\/p\u003e","brand":"Mymadmanlab","offers":[{"title":"Default Title","offer_id":67414928884016,"sku":null,"price":56.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0987\/0809\/5280\/files\/0_34c22380-8ce3-4b42-93c3-aeb9a9b6ce05.png?v=1785400085","url":"https:\/\/mymadmanlab.com\/products\/inside-out-memory-orb-halloween-basket","provider":"Mymadmanlab.com","version":"1.0","type":"link"}