{"product_id":"meta-quest-3-wall-holder","title":"Meta Quest 3 Wall Holder","description":"\u003cp\u003e\u003cstrong\u003eMeta Quest 3 Wall Holder\/Hanger in three versions.\u003c\/strong\u003e\u003c\/p\u003e\u003col\u003e\n\u003cli\u003eHolder for Bare Wall\u003c\/li\u003e\n\u003cli\u003eHolder for Honeycomb Storage Wall (HSW)\u003c\/li\u003e\n\u003cli\u003eHolder for Multiboard\u003c\/li\u003e\n\u003c\/ol\u003e\u003cp\u003eThis Holder have two separate parts. One for Quest 3 Virtual Reality Headset and other Separate Holder for Controllers. Yes after quite a long time of working on and prototyping I decided to make a separate holders. Reasons for that are simple. Right orientations for printing to make a stronger structural build by using as less material as possible to make a totally supportless model and for flexibility so You are not tied to put controllers only on one spot. So yes, to print this holder set , no supports are needed.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e 1. Fitting on Bare Wall\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\u003cli\u003eEasiest and strongest fit. Just screw holders to the wall using screw holes provided on Holders for Bare Wall. Holes are designed for M4 Countersunk Screws. \u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003e2.\u003c\/strong\u003e \u003cstrong\u003eFitting on Honeycomb Storage Wall\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003ePrint a Holder set made for HSW. Parts needed to print are:\u003cbr\u003e- MainHolder_HSW\u003cbr\u003e- ControllerRing_HSW\u003cbr\u003e- HSW_Pin (Need 2 of them)\u003c\/li\u003e\n\u003cli\u003ePush both printed HSW_Pin into sockets you can see on MainHolder_HSW. I would advise to use a bit of superglue to fix them strong in place.\u003c\/li\u003e\n\u003cli\u003euse \u003cstrong\u003einsert-empty.stl \u003c\/strong\u003efrom \u003ca target=\"_blank\" href=\"https:\/\/makerworld.com\/en\/models\/22521#profileId-27457\" rel=\"nofollow noopener\"\u003eOriginal HSW Model\u003c\/a\u003e by RostaP for fitting Holder to the HSW.\u003c\/li\u003e\n\u003cli\u003eAccording to your printer tolerances it is possible that Fitting Pins into MainHolder_HSW and\/or HSW Insert will be very hard or even impossible. If so just use a file or sandpaper to shave a little bit off the pin. I have made a very tight fit for a reason. Loose fit could cause a fall of headset what no one of us would want.\u003c\/li\u003e\n\u003cli\u003eOne more small advise for better fit. Put one or two inserts under lower side of MainHolder_HSW backplate (no matter what kind of) to prevent a bending as any HSW Insert is not flat to wall. Same as for Multiboard. You can check a photo in Multiboard description below what I mean.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003e3. Fitting to Multiboard\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003ePrint a Holder set made for Multiboard. Parts needed to print are:\u003cbr\u003e- MainHolder_Multiboard\u003cbr\u003e- ControllerRing_Multiboard\u003cbr\u003e- Multiboard_Pin (Need 2 of them)\u003c\/li\u003e\n\u003cli\u003ePush both printed Multiboard_Pin into sockets you can see on MainHolder_Multiboard. I would advise to use a bit of superglue to fix them strong in place.\u003c\/li\u003e\n\u003cli\u003euse \u003ca target=\"_blank\" href=\"https:\/\/thangs.com\/designer\/Keep%20Making\/3d-model\/Weight-Bearing%20Directional%20Snap-989145\" rel=\"nofollow noopener\"\u003e\u003cstrong\u003eWeight-Bearing Directional Snap\u003c\/strong\u003e\u003c\/a\u003e\u003cstrong\u003e \u003c\/strong\u003efor fitting Holder to the Multiboard. Probably you can use a \u003cstrong\u003eMultiboard Tight Snap\u003c\/strong\u003e, but I can't confirm that as I haven't checked it. \u003ci\u003e\u003cstrong\u003eDon't use an ordinary \u003c\/strong\u003e\u003c\/i\u003e\u003cstrong\u003eMultiboard Snaps\u003c\/strong\u003e\u003ci\u003e\u003cstrong\u003e as after my tests I found them very unsecure and it is a very big possibility that in one point they will come out causing fall of headset. They could be ok for controllers, but headset is too heavy for them. \u003c\/strong\u003e\u003c\/i\u003e\n\u003c\/li\u003e\n\u003cli\u003eAccording to your printer tolerances it is possible that Fitting Pins into MainHolder_Multiboard and\/or Multiboard Snap will be very hard or even impossible. If so just use a file or sandpaper to shave a little bit off the pin. I have made a very tight fit for a reason. Loose fit could cause a fall of headset what no one of us would want.\u003c\/li\u003e\n\u003cli\u003eOne more small advise for better fit. Put one or two inserts or even better a double one under lower side of MainHolder_Multiboard backplate (no matter what kind of) to prevent a bending as any Multiboard Snap is not flat to Board. Something like on this photo:\u003cbr\u003e \u003c\/li\u003e\n\u003c\/ul\u003e\u003cfigure class=\"image image_resized\" style=\"width: 58.53%\"\u003e\u003cimg src=\"https:\/\/makerworld.bblmw.com\/makerworld\/model\/DSM00000000480943\/design\/2024-06-01_5298523f7240e.jpg\"\u003e\u003c\/figure\u003e\u003cp\u003e\u003cbr\u003eThat's it. I don't think here is anything hard to understand. But if you have any questions or suggestions, just give me a shout.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eYou can Buy me a coffee if You want to support me in my work here :)\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e\u003ca target=\"_blank\" href=\"https:\/\/www.buymeacoffee.com\/warlogh\" rel=\"nofollow noopener\"\u003e\u003cimg src=\"https:\/\/makerworld.bblmw.com\/makerworld\/model\/DSM00000000480943\/design\/2024-03-16_5923e8a1a0113.jpg\"\u003e\u003c\/a\u003e\u003c\/p\u003e\u003cp\u003e\u003ca target=\"_blank\" href=\"https:\/\/www.buymeacoffee.com\/warlogh\" rel=\"nofollow noopener\"\u003ehttps:\/\/www.buymeacoffee.com\/warlogh\u003c\/a\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e(\u003c\/strong\u003eAnd very Big Thank You For interest in my work\u003cstrong\u003e)\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eDesign by warlogh on MakerWorld (license: BY).\u003c\/p\u003e","brand":"Mymadmanlab","offers":[{"title":"Default Title","offer_id":67383090413872,"sku":null,"price":46.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0987\/0809\/5280\/files\/0_df9a1438-b85f-4374-9b93-b488d2360a06.png?v=1784489640","url":"https:\/\/mymadmanlab.com\/products\/meta-quest-3-wall-holder","provider":"Mymadmanlab.com","version":"1.0","type":"link"}