{"product_id":"multiboard-magnetic-cable-mount","title":"Multiboard magnetic cable mount","description":"\u003cp\u003eI have a bunch of cables running around near my Multiboard, and wanted a way to keep them organized and easy accessible. This mount comes in two parts:\u003c\/p\u003e\u003col\u003e\n\u003cli\u003eA snap that goes in the Multiboard, for where you want to mount the cable.\u003c\/li\u003e\n\u003cli\u003eA clamp that goes around the cable to hold the magnets that attach it to the snap.\u003c\/li\u003e\n\u003c\/ol\u003e\u003cp\u003eEach part uses four 6x2mm disc magnets, the same kind that are used in Gridfinity. I went with four because it seemed like the optimum amount to provide a reasonable strength grip even on longer\/heavier cables. If you insert the magnets in the recommended pattern, it also lets the mount self-align when popping it in to place.\u003c\/p\u003e\u003cp\u003eNo supports and no adhesive! All you need are the magnets!\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e\u003cstrong\u003ePrinting instructions\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eThese parts are designed to be printed in the orientation shown in the slicer screenshot.\u003c\/li\u003e\n\u003cli\u003eThe Multiboard snap is a remix of the original snap, which was designed to be printed with 3 walls. The other parts are fine with 2.\u003c\/li\u003e\n\u003cli\u003eDesigned and tested with standard PLA on a 0.4mm nozzle.\u003c\/li\u003e\n\u003cli\u003eNo supports needed!\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eAssembly instructions\u003c\/strong\u003e\u003c\/p\u003e\u003col\u003e\n\u003cli\u003eDecide on the orientation you want the cable to sit when mounted to the Multiboard.\u003c\/li\u003e\n\u003cli\u003eInsert the magnets in the recommended pattern (see “Inserting magnets” below) in the Multiboard snap.\u003c\/li\u003e\n\u003cli\u003eFigure out what orientation the snap will be in when inserted into the Multiboard. This likely depends on how you plan to insert the A side snap on the back.\u003c\/li\u003e\n\u003cli\u003eWith that orientation in mind, insert magnets into the cable clamp in the opposite direction from the Multiboard, so they'll attract each other with the mount oriented how you want.\u003c\/li\u003e\n\u003cli\u003ePlace your cable in the top side of the clamp, and press the bottom side into the slots until it clicks.\u003c\/li\u003e\n\u003c\/ol\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eInserting magnets\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe magnet holes on both parts have a small lip around them at the opening. This holds the magnets in place without needing any adhesives. The magnets are not meant to be removed once inserted.\u003c\/p\u003e\u003cp\u003eInserting the magnets by hand can be a bit tricky, but the included magnet insertion tool makes it much easier. Here's my recommended method for inserting the magnets:\u003c\/p\u003e\u003col\u003e\n\u003cli\u003ePlace the insertion tool on top of the piece you want to insert the first magnet in to. The flat side should be facing up, and the tiered side should be facing down and holding the other piece in place. The holes should be aligned on both parts.\u003c\/li\u003e\n\u003cli\u003eDrop in a single magnet in the first position (it doesn't matter where you start), and get it oriented how you want. This is easiest if you hold another magnet underneath the part, so the magnet you're inserting will orient itself.\u003c\/li\u003e\n\u003cli\u003ePlace the peg in the hole on top of the magnet being inserted, careful to hold the magnet in place in the orientation you want.\u003c\/li\u003e\n\u003cli\u003eGive the peg a light tap with a rubber mallet or some other whacking device.\u003cul\u003e\u003cli\u003eBe careful not to hit it too hard, or you may push the magnet all the way through the bottom of the snap.\u003c\/li\u003e\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003cli\u003eRepeat this process for the three remaining magnets, going in a circle. When using the recommended magnet layout, each subsequent magnet will be attracted to the magnet adjacent to it, so it will align itself to the correct orientation.\u003c\/li\u003e\n\u003c\/ol\u003e\u003cp\u003eNote: It does not matter which pole you decide to call “north” and which is “south”, as long as you're consistent about it.\u003c\/p\u003e\u003cp\u003eDesign by Garrett on MakerWorld (license: BY).\u003c\/p\u003e","brand":"Mymadmanlab","offers":[{"title":"Default Title","offer_id":67414981345584,"sku":null,"price":4.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0987\/0809\/5280\/files\/0_d86ad2f9-202d-41e3-b4c2-c376bf833c60.png?v=1785402581","url":"https:\/\/mymadmanlab.com\/products\/multiboard-magnetic-cable-mount","provider":"Mymadmanlab.com","version":"1.0","type":"link"}