{"product_id":"p1s-poop-bin-with-tool-holder-clean-front-face","title":"P1S Poop Bin with Tool Holder - Clean Front Face","description":"\u003cp\u003eThis is a slight remix\/change from JetSpool's adaptation work (original eclien's work), as my Spool clips are different, hence \u003ci\u003eI didn't need the 2x holes in the Front Face for holding  clips, so I removed it! \u003c\/i\u003e=D  This way you have a simpler and clean face. \u003c\/p\u003e\u003cp\u003eIn addition, I normally give names for my favorite toys, like Car, Bike, Boat, etc.… in that case I obviously have a name for my 3D printer: which is “Bambinha”. So, for those that are like me, I've included a Text Negative Part to this project, so that you can “engrave” any name\/text you wish in the Front Face of the Poop Collector\/Tool Holder, showing your printer name, any funny text, etc.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e****************************************\u003cstrong\u003eIMPORTANT\u003c\/strong\u003e*****************************************\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003ePlease NOTE that this file\/project is for \u003cstrong\u003e\u003cu\u003e0.8mm NOOZLE\u003c\/u\u003e\u003c\/strong\u003e!\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eTHEREFORE, it prints much QUICKER: \u003cu\u003e6HRS \u003c\/u\u003e(3 hrs. less compared to JetSpool's project), BUT  it lacks fine details (I don't mind since it is just the Poop Collector for the printer), even though it was very well printed!\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eSO, if you are looking for a very fine; detailed; pristine part, this may not be for you! However, it still printing perfectly and it does the job exactly as it should (even without the magnets)\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e------------------------------------------------------------\u003cstrong\u003eGlobal Settings Changes\u003c\/strong\u003e------------------------------------------------------------\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e*Aiming for printing time, I used:\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e0.56mm\u003c\/strong\u003e \u003cstrong\u003eLayer height\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIncreased Inner Wall speed to 160mm\/s\u003c\/p\u003e\u003cp\u003eIncreased Sparse Infill speed to 120mm\/s\u003c\/p\u003e\u003cp\u003eIncreased Internal Solid Infill speed to 170mm\/s\u003c\/p\u003e\u003cp\u003eUsed Standard\/Normal speed printer (Changing it to Ludacris will cause layer issues with these config - too quick!)\u003c\/p\u003e\u003cp\u003e-------------------------------------------------------------------------------------------------------------------------------------------------------------\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eUsing the config above reduced the printing time by ⅓, as mentioned above, however it slightly increased amount of material (35g more)\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eI have used P1S to print it. \u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e*My Printer \u003cstrong\u003ehas the Anti-Vibration feet (2025 version) installed\u003c\/strong\u003e, so the “opening” for the purge chute was slightly lower than the actual bottom point of the purge chute. Because I didn't have anything to do with my \u003cu\u003eoriginal fee\u003c\/u\u003et (still had a very amount of glue on it), I used it underneath the Poop collector to align the holes and it worked perfectly! (see 5th photo of this profile).\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e*So basically this print is designed for printers with the \u003cstrong\u003e\u003cu\u003eoriginal feet\u003c\/u\u003e\u003c\/strong\u003e; however it also works perfectly for printers with Anti-Vibration feet  if you use the original ones underneath the printed part.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003ePrinted using Bambu Black PLA Basic filament.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eThanks to the original project creator's, the angles are not bigger than 45º, so \u003cstrong\u003e\u003cu\u003eNO SUPPORT\u003c\/u\u003e\u003c\/strong\u003e\u003cu\u003e needed\u003c\/u\u003e for this print.\u003c\/p\u003e\u003cp\u003eThere is only 2x internal overhang walls for the Disc Magnets holes, on which the printer handled it totally fine without any support!\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eAs the part uses most of the build plate, the first layer may bond to the Custom filament, however it did not cause any damage to the part when I removed mine using tools.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eLet me know If you have any suggestions\/improvement\/feedback for this model\/project. If I find spare time, I can possibly work on editing the 3D model and personalize it for you.\u003c\/p\u003e\u003cp\u003eDesign by CaTiTo Ragacci on MakerWorld (license: BY-SA).\u003c\/p\u003e","brand":"Mymadmanlab","offers":[{"title":"Default Title","offer_id":67391365546288,"sku":null,"price":53.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0987\/0809\/5280\/files\/0_baa5b156-9b97-42f8-a5b8-7ebf00884bf4.png?v=1784748813","url":"https:\/\/mymadmanlab.com\/products\/p1s-poop-bin-with-tool-holder-clean-front-face","provider":"Mymadmanlab.com","version":"1.0","type":"link"}