{"product_id":"quick-calibration-print","title":"Quick Calibration Print","description":"\u003cp\u003eThis model is designed to test several different aspects of your printer's calibration.  If there are problems, then you need to take measures to adjust the slicer settings or printer calibrations as needed.\u003c\/p\u003e\u003cp\u003eSo, what are you measuring?\u003c\/p\u003e\u003cfigure class=\"image image_resized\" style=\"width:50%;\"\u003e\u003cimg src=\"https:\/\/makerworld.bblmw.com\/makerworld\/draft\/603937\/2024-02-29_iz9zhpeviotm.png\"\u003e\u003c\/figure\u003e\u003cp\u003eThe thickness of the card at the edge is 3mm.\u003c\/p\u003e\u003cp\u003eThe card is 75mm wide.\u003c\/p\u003e\u003cfigure class=\"image image_resized\" style=\"width:50%;\"\u003e\u003cimg src=\"https:\/\/makerworld.bblmw.com\/makerworld\/draft\/603937\/2024-02-29_nch1v1wajjsl.png\"\u003e\u003c\/figure\u003e\u003cp\u003e50mm in the y direction.\u003c\/p\u003e\u003cfigure class=\"image image_resized\" style=\"width:50%;\"\u003e\u003cimg src=\"https:\/\/makerworld.bblmw.com\/makerworld\/draft\/603937\/2024-02-29_qv7zcsy0spbl.png\"\u003e\u003c\/figure\u003e\u003cp\u003eand 50mm diagonal measure using the alignment arrows.\u003c\/p\u003e\u003cfigure class=\"image image_resized\" style=\"width:50%;\"\u003e\u003cimg src=\"https:\/\/makerworld.bblmw.com\/makerworld\/draft\/603937\/2024-02-29_bg0lh8mtg6hr.png\"\u003e\u003c\/figure\u003e\u003cp\u003eIf the X, Y, or card thickness are off by more than just a few 100ths mm you should probably look into recalibrating your printer.  There is a good test print and instructions for how to make adjustments to a Marlin based printer \u003ca href=\"https:\/\/www.printables.com\/model\/387529-quick-xyz-axis-calibration-test\" rel=\"nofollow\"\u003eavailable\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003eEach step in the recessed stairway is 0.2mm.\u003c\/p\u003e\u003cfigure class=\"image image_resized\" style=\"width:50%;\"\u003e\u003cimg src=\"https:\/\/makerworld.bblmw.com\/makerworld\/draft\/603937\/2024-02-29_elwkhsupkop5.png\"\u003e\u003c\/figure\u003e\u003cp\u003eThin lines ranging from 0.25mm up to 3.0mm\u003c\/p\u003e\u003cfigure class=\"image image_resized\" style=\"width:50%;\"\u003e\u003cimg src=\"https:\/\/makerworld.bblmw.com\/makerworld\/draft\/603937\/2024-02-29_07k7pifig5f8.png\"\u003e\u003c\/figure\u003e\u003cp\u003eOverhang tests that range from 50-65 degrees.\u003c\/p\u003e\u003cfigure class=\"image image_resized\" style=\"width:50%;\"\u003e\u003cimg src=\"https:\/\/makerworld.bblmw.com\/makerworld\/draft\/603937\/2024-02-29_n928v3l8k8vo.png\"\u003e\u003c\/figure\u003e\u003cp\u003eOverhang problems are frequently caused by cooling problems.\u003c\/p\u003e\u003cfigure class=\"image image_resized\" style=\"width:50%;\"\u003e\u003cimg src=\"https:\/\/makerworld.bblmw.com\/makerworld\/draft\/603937\/2024-02-29_t84tzjined8y.png\"\u003e\u003c\/figure\u003e\u003cp\u003eRound holes that pass all of the way through the card are 10mm and 5mm respectively. The raised circle is 10mm in diameter. The diameter of the outer circle is 15mm.\u003c\/p\u003e\u003cblockquote\u003e\u003cp\u003eIf these are off you can find adjustments in your slicer to handle hole size problems.\u003c\/p\u003e\u003c\/blockquote\u003e\u003cfigure class=\"image image-style-align-center image_resized\" style=\"width:50%;\"\u003e\u003cimg src=\"https:\/\/makerworld.bblmw.com\/makerworld\/draft\/603937\/2024-02-29_l9pm6xa6hk7x.png\"\u003e\u003c\/figure\u003e\u003cp\u003eOther features include:\u003c\/p\u003e\u003cp\u003eClearance test (small teeth whose gaps decrease)\u003c\/p\u003e\u003cblockquote\u003e\u003cp\u003eSometimes problems with small gaps can be related to under or over extrusion.\u003c\/p\u003e\u003c\/blockquote\u003e\u003cp\u003eRetraction tests (two short spikes sticking up beside the bridging test)\u003c\/p\u003e\u003cblockquote\u003e\u003cp\u003eStringing between the spikes can be addressed by adjusting the retraction settings in your slicer.\u003c\/p\u003e\u003c\/blockquote\u003e\u003cp\u003eBridging tests\u003c\/p\u003e\u003cblockquote\u003e\u003cp\u003eFailures in the bridging test are often attributed to insufficient cooling.\u003c\/p\u003e\u003c\/blockquote\u003e\u003cp\u003eBreak out your calipers and start measuring to figure out where your printer needs work.\u003c\/p\u003e\u003ch3\u003ePrinting\u003c\/h3\u003e\u003cp\u003ePrint using 0.2mm layer height.\u003cbr\u003eNo supports.\u003c\/p\u003e\u003cp\u003e0.4mm nozzle works best.\u003c\/p\u003e\u003ch3\u003eHistory\u003c\/h3\u003e\u003cp\u003e2023-05-12: Add new updated model that includes a stringing test.\u003c\/p\u003e\u003cp\u003eDesign by grizzie17 on MakerWorld (license: BY).\u003c\/p\u003e","brand":"Mymadmanlab","offers":[{"title":"Default Title","offer_id":67408714105136,"sku":null,"price":4.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0987\/0809\/5280\/files\/0_64c0fc47-c09e-4f62-bd8b-e4055849b93f.png?v=1785226830","url":"https:\/\/mymadmanlab.com\/products\/quick-calibration-print","provider":"Mymadmanlab.com","version":"1.0","type":"link"}