{"product_id":"snapmaker-u1-feeder-relocation-rear-position","title":"Snapmaker U1 Feeder Relocation – Rear Position","description":"\u003cp\u003eCould someone please post the exact height of a prefeeder (housing only, without the PTFE retaining ring) in the comments when they get a chance?\u003c\/p\u003e\u003cp\u003eI'd like to add a requested upside-down version, but I'd rather not pull my printer out of the cabinet just to take the measurement.\u003c\/p\u003e\u003cp\u003eBTW, I can't reply to some comments because those users have their settings configured to only allow messages from Level 7 and above. As far as I can tell, that seems to be the default setting on MakerWorld.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e***\u003c\/p\u003e\u003cp\u003eUPDATE 10.04.2026\u003c\/p\u003e\u003cp\u003eI have replaced the profiles with ones containing four build plates. The following versions are included:\u003cbr\u003eV1.0 - classic version with feeder holders that fit snugly to the housing curves, PC4-M6\u003cbr\u003eV1.1 - classic version with feeder holders that fit snugly to the housing curves, PC4-M10\u003cbr\u003eV2.0 - version with flat contact surface and larger channels for extensions, PC4-M6\u003cbr\u003eV2.1 - version with lflat contact surface and larger channels for extensions, PC4-M10\u003cbr\u003e\u003cbr\u003eSince some users have reported that the filament cannot be fed all the way to the prefeeder and tends to jam when using PC4-M6 fittings, I recommend printing one of the PC4-M10 versions. With these connectors, the tubes can be guided through the fitting all the way to the prefeeder.\u003c\/p\u003e\u003cp\u003eLet me know if, against expectations, anything does not fit properly.\u003cbr\u003eOverall, I would really appreciate feedback on V2.1. And of course also on the other versions.\u003c\/p\u003e\u003cp\u003eSince there also seem to be differences in the prefeder mounting between the crowdfunding and post-crowdfunding versions, I would be grateful if someone could measure the retaining tabs and draw a small sketch and provide it to me. The dimensions of the mounting points to the rear wall are also of interest, as there may have been changes there as well.\u003c\/p\u003e\u003cp\u003e***\u003cbr\u003e\u003cbr\u003e***\u003c\/p\u003e\u003cp\u003eUPDATE 30.03.2026\u003c\/p\u003e\u003cp\u003eI have added a V2, which should be both easier to print and easier to assemble. Since my printer is already set up and I don’t have the time to test the new mounts, I would appreciate it if someone who tries them could share their experience and provide pictures.\u003c\/p\u003e\u003cp\u003eThe mounting points of the dovetail guides are identical to the first version. The feeder holders are compatible with the feeder holder adapters from V1.\u003c\/p\u003e\u003cp\u003e***\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e***\u003cbr\u003eUPDATE: \u003cbr\u003eThere are now flat cable extensions available on AliExpress (you will need the one with 15 pins):\u003c\/p\u003e\u003cp\u003e\u003ca target=\"_blank\" rel=\"noopener noreferrer ugc\" href=\"https:\/\/www.aliexpress.com\/item\/1005010637306932.html\"\u003ehttps:\/\/www.aliexpress.com\/item\/1005010637306932.html\u003c\/a\u003e restocked!\u003cbr\u003e\u003ca target=\"_blank\" rel=\"noopener noreferrer ugc\" href=\"https:\/\/www.aliexpress.com\/item\/1005011802248041.html\"\u003ehttps:\/\/www.aliexpress.com\/item\/1005011802248041.html\u003c\/a\u003e restocked!\u003c\/p\u003e\u003cp\u003e\u003cbr\u003eThis will save you most of the work. However, I haven't personally tested it yet, and I'm not sure if there is enough room for the connectors in the current model or if you can push them into the printer. If you try it, let me know if the adapters need to be adjusted.\u003cbr\u003e***\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eI designed an adapter kit that allows the U1’s feeders to be relocated to the back of the printer. No drilling is required, as the original mounting points of the feeders are used for attachment.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eThis makes it possible to install the printer in a 50 cm PAX cabinet from IKEA or other cabinets of similar dimensions. I use a pull-out shelf for the printer and another pull-out shelf underneath for a Chitu E1 filament dryer, which supplies the filament.\u003c\/p\u003e\u003cp\u003eThe ribbon cables for the feeders need to be rerouted so that their length is sufficient for the modification. For this, the side panels must be removed. Additionally, a configuration adjustment in Klipper is required to account for the shortened feed path (approximately 150 mm).\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eFor these adjustments, I use the custom firmware from \u003ca target=\"_blank\" rel=\"noopener noreferrer ugc\" href=\"https:\/\/github.com\/paxx12\/SnapmakerU1-Extended-Firmware\"\u003epaxx12\u003c\/a\u003e. Download the latest release file (U1_extended_...bin), copy it to a FAT32-formatted USB drive, and connect it to the printer. Then navigate on the touchscreen to \u003cstrong\u003eSettings → About → Firmware → Local Update\u003c\/strong\u003e and select the file.\u003c\/p\u003e\u003cp\u003eThe update process takes a few minutes, and the printer will restart afterward. Check the IP address under Wi-Fi or LAN mode and use it to connect to Klipper (Fluidd) through your browser.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eIn the interface, switch to the \u003cstrong\u003eConfig\u003c\/strong\u003e menu. Then navigate to the subfolder \u003cstrong\u003eextended\/Klipper\u003c\/strong\u003e. At this location, create a new .cfg file. I named it feeders.cfg. Add the following lines to this document:\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e[filament_feed left]\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003epreload_length: 800\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e[filament_feed right]\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003epreload_length: 800 \u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eThe original settings will now be overridden with these values. The original values are 950.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eNow regarding the models:\u003c\/p\u003e\u003cp\u003eI highly recommend using the file \u003cstrong\u003eOrcaSlicer_Snapmaker U1 Feeder Relocation – Rear Position.3mf\u003c\/strong\u003e. Open the dropdown menu in the download section and select \u003cstrong\u003eDownload STL\/CAD\u003c\/strong\u003e. Contrary to what one might expect, the \u003cstrong\u003e3MF\u003c\/strong\u003e for OrcaSlicer is found there. For direct download, Makerworld only allows \u003cstrong\u003eBambu 3MF files\u003c\/strong\u003e. \u003cbr\u003eI have also included the OBJ files. However, in that case, you will need to configure supports, wall thickness, and orientation yourself. The dovetail guides work best when printed in a vertical orientation.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eThe adapters for the side mounts should be printed with at least three wall lines, as the full weight will later hang from the four hooks. I printed all parts with PLA; PETG should work just as well, although I haven’t tested it.\u003c\/p\u003e\u003cp\u003eAdditionally, you will need four PTFE push-fit connectors with 4–5 mm long M6 threads to complete the assembly.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eI uploaded a tutorial on YouTube, in German and English.\u003cbr\u003eGerman: \u003ca target=\"_blank\" rel=\"noopener noreferrer ugc\" href=\"https:\/\/youtu.be\/rKON5yg1FRU\"\u003ehttps:\/\/youtu.be\/rKON5yg1FRU\u003c\/a\u003e\u003cbr\u003eEnglish: \u003ca target=\"_blank\" rel=\"noopener noreferrer ugc\" href=\"https:\/\/youtu.be\/FhLfrULrGfg\"\u003ehttps:\/\/youtu.be\/FhLfrULrGfg\u003c\/a\u003e\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eModels for Chitu Display Mod:\u003cbr\u003e\u003ca target=\"_blank\" rel=\"noopener noreferrer ugc\" href=\"https:\/\/makerworld.com\/de\/models\/2443973-chitu-e1-display-relocation#profileId-2682242\"\u003ehttps:\/\/makerworld.com\/de\/models\/2443973-chitu-e1-display-relocation#profileId-2682242\u003c\/a\u003e\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eChitu Tutorial (German):\u003cbr\u003e\u003ca target=\"_blank\" rel=\"noopener noreferrer ugc\" href=\"https:\/\/youtu.be\/4JsouTocAKw\"\u003ehttps:\/\/youtu.be\/4JsouTocAKw\u003c\/a\u003e\u003cbr\u003e \u003c\/p\u003e\u003cp\u003eFor some reason, my reply below to the comment about the dryer isn’t visible outside my account. \u003cbr\u003e \u003c\/p\u003e\u003cp\u003eThis is my first upload. I would appreciate a like or boost if my contribution helps. I am also open to suggestions and comments.\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eJanzi\u003c\/p\u003e\u003cp\u003eDesign by JanzisTechStuff on MakerWorld (license: BY).\u003c\/p\u003e","brand":"Mymadmanlab","offers":[{"title":"Default Title","offer_id":67369984065840,"sku":null,"price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0987\/0809\/5280\/files\/0_a3523539-1ac6-468c-9340-ecef4c2df19f.png?v=1784090570","url":"https:\/\/mymadmanlab.com\/products\/snapmaker-u1-feeder-relocation-rear-position","provider":"Mymadmanlab.com","version":"1.0","type":"link"}