{"product_id":"supernote-nomad-folio-stiffeners","title":"Supernote Nomad Folio Stiffeners","description":"\u003cp\u003eThis project provides the liner pieces for DIY folio cases for the Supernote Nomad from Ratta. See Ratta's guide for DIY folio cases here:\u003c\/p\u003e\u003cp\u003e\u003ca target=\"_blank\" href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0565\/1945\/9007\/files\/A6X2NomadFolioDIYGuide_Version.1.pdf?v=1724296669\" rel=\"nofollow noopener\"\u003ehttps:\/\/cdn.shopify.com\/s\/files\/1\/0565\/1945\/9007\/files\/A6X2NomadFolioDIYGuide_Version.1.pdf?v=1724296669\u003c\/a\u003e\u003c\/p\u003e\u003cp\u003eTo complete this project, you will need the DIY folio kit sold here:\u003c\/p\u003e\u003cp\u003e\u003ca target=\"_blank\" href=\"https:\/\/supernote.com\/products\/diy-kit-for-folio-of-nomad?srsltid=AfmBOooMcmBXOkNFT4N96--1FqyxB2YY_GRuJxFZrIQpos0KzeP3nZjC\" rel=\"nofollow noopener\"\u003ehttps:\/\/supernote.com\/products\/diy-kit-for-folio-of-nomad?srsltid=AfmBOooMcmBXOkNFT4N96--1FqyxB2YY_GRuJxFZrIQpos0KzeP3nZjC\u003c\/a\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eImportant Notes:\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eThe uploaded STLs are designed to allow the liners to be printed in single monolithic pieces. \u003ci\u003e\u003cstrong\u003eYou will need insert a pause in your slicer after the last layer of what Ratta calls \"layer 2\", insert the hall sensor magnets and\/or magnet shields in the correct orientation, and resume printing for the last layer.\u003c\/strong\u003e\u003c\/i\u003e  These pauses are included in the uploaded print profile.\u003cbr\u003e\u003cbr\u003eIF you prefer to print the layers individually (which I do not recommend), the OpenSCAD file has a flag which will allow you to do so.\u003cbr\u003e \u003c\/li\u003e\n\u003cli\u003e\n\u003ci\u003e\u003cstrong\u003eDO NOT insert the screws during the print.\u003c\/strong\u003e\u003c\/i\u003e If you do, the nozzle will hit the screw shafts while printing the final layer. Instead, insert the screws after the print is done, and if desired, glue in the round spacers to fill the empty space in the first layer.\u003cbr\u003e \u003c\/li\u003e\n\u003cli\u003eTwo versions of the STLs are uploaded: one with a \"thin\" liner, and one in which the total thickness of the covers has been increased to 2.5 mm for added stiffness. You can adjust this thickness in the OpenSCAD file if you prefer something different.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003ePrinting tips:\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eThe uploaded STLs are optimized for an 0.2 mm layer height (the component thicknesses from Ratta's technical drawings are rounded up to the nearest 0.2 mm). If you want to print with a different layer height, load the OpenSCAD file and change the layer_height parameter in the customizer.\u003cbr\u003e\u003cbr\u003eNote also that the \"thin\" layers in Ratta's design (the ones that are marked as 0.2 mm thick) have been increased to 0.4 mm so that the magnets are covered by 2 layers of filament rather than one. If you wish to change this, change the \"min_layer_num\" parameter in the OpenSCAD file.\u003cbr\u003e \u003c\/li\u003e\n\u003cli\u003e\n\u003ci\u003e\u003cstrong\u003ePrint the tester.stl file BEFORE you print the entire project,\u003c\/strong\u003e\u003c\/i\u003e and make sure that the magnet shielding squares, screws, and hall magnets fit in the corresponding holes. If they don't, adjust your slicer's X-Y hole compensation as needed until they fit.\u003cbr\u003e \u003c\/li\u003e\n\u003cli\u003eIf you have trouble with the print not correctly bridging over the magnets \u0026amp; magnet shields after these are inserted and the print is resumed, try the following:\u003cbr\u003e\u003cbr\u003e \u003cul\u003e\n\u003cli\u003eEnable the \"thick bridge\" option in your slicer (this is what it is called in Bambu Studio - may have other names in other slicers).\u003cbr\u003e \u003c\/li\u003e\n\u003cli\u003eWipe down the magnet shields and Hall sensor magnets with rubbing alcohol to remove fingerprints before inserting.\u003cbr\u003e\u003cbr\u003e\u003ci\u003e\u003cstrong\u003eCAUTION\u003c\/strong\u003e\u003c\/i\u003e: the mark Ratta uses to indicate the \"north\" side of the Hall sensor magnets WILL wash off with rubbing alcohol. If you do this, be very careful to not lose track of the correct orientation of the magnet!\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003eAssembly:\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eInsert the Hall sensor magnets and magnet shields during printing as noted above.\u003c\/li\u003e\n\u003cli\u003eAfter printing, insert the screws and screw in the magnets that secure the device.\u003c\/li\u003e\n\u003cli\u003eIf desired, insert the circular \"plugs\" for the screw holes on the outside of the back cover and glue in place.\u003c\/li\u003e\n\u003cli\u003eGlue in a pen loop.\u003c\/li\u003e\n\u003cli\u003eGlue the liners (with magnets) to your cover material of choice.\u003c\/li\u003e\n\u003cli\u003eLet the glue cure, and then enjoy your new folio!\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eFeel free to remix and\/or use as the basis for other folio variations :-)\u003c\/p\u003e\u003cp\u003eDesign by chemistbyday on MakerWorld (license: BY-SA).\u003c\/p\u003e","brand":"Mymadmanlab","offers":[{"title":"Default Title","offer_id":67414978920752,"sku":null,"price":12.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0987\/0809\/5280\/files\/0_c2f22cc8-441e-4d0a-a308-8773f2f9ec7a.jpg?v=1785402463","url":"https:\/\/mymadmanlab.com\/products\/supernote-nomad-folio-stiffeners","provider":"Mymadmanlab.com","version":"1.0","type":"link"}