{"product_id":"ultimate-miniature-figurine-settings-0-4-0-2","title":"Ultimate Miniature\/Figurine settings (0.4\/0.2)","description":"\u003cp\u003eHello everyone!\u003c\/p\u003e\u003cp\u003eThis is my \u003cstrong\u003eUltimate Preset for Miniatures and Figurines\u003c\/strong\u003e. The preset has been tested across all Bambu Lab machines (from A1 Mini to H2C) by me and some friends to ensure reliable results.\u003c\/p\u003e\u003cp\u003eThere are \u003cstrong\u003etwo profiles included\u003c\/strong\u003e:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eone for \u003cstrong\u003e0.4 mm nozzles\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eone for \u003cstrong\u003e0.2 mm nozzles\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThe main differences between them are \u003cstrong\u003eline width\u003c\/strong\u003e and \u003cstrong\u003elayer height\u003c\/strong\u003e, optimized for each nozzle size.\u003c\/p\u003e\u003ch2\u003eImportant – Required Preparation\u003c\/h2\u003e\u003cp\u003eThese settings depend on proper setup. Without it, prints may fail.\u003c\/p\u003e\u003cp\u003ePlease make sure:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eYou are using \u003cstrong\u003edry and calibrated filament\u003c\/strong\u003e (Pressure Advance, Flow Rate, Bridging, Overhangs)\u003cbr\u003e→ Guide: \u003ca target=\"_blank\" rel=\"noopener noreferrer ugc\" href=\"https:\/\/github.com\/OrcaSlicer\/OrcaSlicer\/wiki\/calibration_guide\"\u003ehttps:\/\/github.com\/OrcaSlicer\/OrcaSlicer\/wiki\/calibration_guide\u003c\/a\u003e\n\u003c\/li\u003e\n\u003cli\u003eYour build plate is \u003cstrong\u003eproperly cleaned\u003c\/strong\u003e (dish soap + warm water)\u003cbr\u003e→ Guide: \u003ca target=\"_blank\" rel=\"noopener noreferrer ugc\" href=\"https:\/\/youtu.be\/8QIy3aUU8eo?si=mSR3x5sQ-kY2HJJN\"\u003ehttps:\/\/youtu.be\/8QIy3aUU8eo?si=mSR3x5sQ-kY2HJJN\u003c\/a\u003e\n\u003c\/li\u003e\n\u003cli\u003eYou use a plate with \u003cstrong\u003egood adhesion\u003c\/strong\u003e (personal recommendation: Juupine Geco Plate for PLA) or apply glue\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eMiniatures often have \u003cstrong\u003every small contact areas\u003c\/strong\u003e, so good adhesion is critical—this is why we avoid using a brim.\u003c\/p\u003e\u003ch2\u003eSettings You May Want to Adjust\u003c\/h2\u003e\u003cp\u003e(Some of these are even more important depending on model\/filament)\u003c\/p\u003e\u003ch3\u003eIroning\u003c\/h3\u003e\u003cp\u003eIroning smooths top surfaces by re-passing the nozzle over printed layers.\u003cbr\u003eUsually not necessary for miniatures, but can improve flat surfaces.\u003cbr\u003eMust be calibrated per filament—there is no universal setting.\u003cbr\u003e→ Guide: \u003ca target=\"_blank\" rel=\"noopener noreferrer ugc\" href=\"https:\/\/makerworld.com\/de\/models\/2083080-advanced-top-surface-guide-understand-improve\"\u003ehttps:\/\/makerworld.com\/de\/models\/2083080-advanced-top-surface-guide-understand-improve\u003c\/a\u003e\u003c\/p\u003e\u003ch3\u003eArachne Wall Generation (Important)\u003c\/h3\u003e\u003cp\u003eArachne dynamically adjusts line width for better detail.\u003cbr\u003eHowever, it can sometimes introduce artifacts or damage textures.\u003c\/p\u003e\u003cp\u003e→Recommendation: Turn it \u003cstrong\u003eoff whenever possible\u003c\/strong\u003e.\u003cbr\u003eIt is enabled by default for compatibility but can be disabled easily.\u003cbr\u003e(the low line wdith we set before will ensure will still get the most detail possible)\u003c\/p\u003e\u003ch3\u003eSeam (Semi-important)\u003c\/h3\u003e\u003cp\u003eSeam scarfing is enabled to improve surface quality by blending the seam into the model (similar to vase-mode behavior).\u003c\/p\u003e\u003cp\u003eWorks well with default settings, but I recommend testing it yourself.\u003cbr\u003e→ Guide: \u003ca target=\"_blank\" rel=\"noopener noreferrer ugc\" href=\"https:\/\/www.youtube.com\/watch?v=vl0FT339jfc\"\u003ehttps:\/\/www.youtube.com\/watch?v=vl0FT339jfc\u003c\/a\u003e\u003c\/p\u003e\u003ch3\u003eWall Count (Semi-important)\u003c\/h3\u003e\u003cp\u003eDefault is \u003cstrong\u003e2 walls\u003c\/strong\u003e.\u003cbr\u003eYou can increase this for stronger parts.\u003cbr\u003e→Remember: \u003cstrong\u003eWalls are stronger than infill.\u003c\/strong\u003e\u003c\/p\u003e\u003ch3\u003eSpeed \u0026amp; Acceleration (Semi-important)\u003c\/h3\u003e\u003cp\u003eBalanced between quality and speed.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFor \u003cstrong\u003every small models\u003c\/strong\u003e you may reduce speed\u003c\/li\u003e\n\u003cli\u003eFor \u003cstrong\u003elarger figurines\u003c\/strong\u003e you may increase it\u003cbr\u003e(we want to have out wall to be the slowest as its the one we will actually see)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003e\n\u003cbr\u003eSupport (VERY IMPORTANT)\u003c\/h3\u003e\u003cp\u003eSupports will often decide whether your print succeeds or fails.\u003c\/p\u003e\u003cp\u003eMost important setting:\u003c\/p\u003e\u003cul\u003e\u003cli\u003e\n\u003cstrong\u003eTop Z Distance\u003c\/strong\u003e\u003cul\u003e\n\u003cli\u003eMore distance → easier removal, worse surface\u003c\/li\u003e\n\u003cli\u003eLess distance → harder removal, better surface\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\u003c\/ul\u003e\u003cp\u003eThere are two types of supports:\u003c\/p\u003e\u003col\u003e\n\u003cli\u003eSupporting drooping filament\u003c\/li\u003e\n\u003cli\u003eSupporting areas you print \u003ci\u003eon top of\u003c\/i\u003e (most critical)\u003c\/li\u003e\n\u003c\/ol\u003e\u003cp\u003e̶i̶’̶m̶̶ ̶̶c̶̶u̶̶r̶̶r̶̶e̶̶n̶̶t̶̶l̶̶y̶̶ ̶̶w̶̶o̶̶r̶̶k̶̶i̶̶n̶̶g̶̶ ̶̶o̶̶n̶̶ ̶̶a̶̶ ̶̶p̶̶r̶̶o̶̶p̶̶e̶̶r̶̶ ̶̶t̶̶e̶̶s̶̶t̶̶ ̶̶m̶̶o̶̶d̶̶e̶̶l̶̶ ̶̶f̶̶o̶̶r̶̶ ̶̶t̶̶h̶̶i̶̶s̶̶ ̶̶a̶̶n̶̶d̶̶ ̶̶w̶̶i̶̶l̶̶l̶̶ ̶̶u̶̶p̶̶l̶̶o̶̶a̶̶d̶̶ ̶̶i̶̶t̶̶ ̶̶i̶̶n̶̶ ̶̶t̶̶h̶̶e̶̶ ̶̶f̶̶u̶̶t̶̶u̶̶r̶̶e̶̶.̶\u003c\/p\u003e\u003cp\u003e̶i̶̶n̶̶ ̶̶t̶̶h̶̶e̶̶ ̶̶m̶̶e̶̶a̶̶n̶̶t̶̶i̶̶m̶̶e̶̶,̶̶ ̶̶y̶̶o̶̶u̶̶ ̶̶c̶̶a̶̶n̶̶ ̶̶u̶̶s̶̶e̶̶ ̶̶e̶̶x̶̶i̶̶s̶̶t̶̶i̶̶n̶̶g̶̶ ̶̶t̶̶e̶̶s̶̶t̶̶ ̶̶m̶̶o̶̶d̶̶e̶̶l̶̶s̶̶ ̶̶o̶̶n̶̶ ̶̶m̶̶a̶̶k̶̶e̶̶r̶̶w̶̶o̶̶r̶̶l̶̶d̶̶.̶\u003cbr\u003e\u003cbr\u003eHere is the test model: \u003ca target=\"_blank\" rel=\"noopener noreferrer ugc\" href=\"https:\/\/makerworld.com\/de\/models\/2741934-ultimate-support-calibration-tool-top-bottom-z\"\u003ehttps:\/\/makerworld.com\/de\/models\/2741934-ultimate-support-calibration-tool-top-bottom-z\u003c\/a\u003e\u003c\/p\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eAlso make sure to calibrate your \u003cstrong\u003ebridging settings\u003c\/strong\u003e to reduce the need for supports:\u003cbr\u003e→ \u003ca target=\"_blank\" rel=\"noopener noreferrer ugc\" href=\"https:\/\/makerworld.com\/de\/models\/1916063-unsupported-bridge-experiments\"\u003ehttps:\/\/makerworld.com\/de\/models\/1916063-unsupported-bridge-experiments\u003c\/a\u003e\u003c\/p\u003e\u003ch3\u003eSkirts\u003c\/h3\u003e\u003cp\u003eI added \u003cstrong\u003e2 skirt layers\u003c\/strong\u003e:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFirst layer primes the nozzle\u003c\/li\u003e\n\u003cli\u003eSecond layer primes the nozzle after the first layer inspection\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e \u003c\/p\u003e\u003cp\u003eHow to save the preset: \u003c\/p\u003e\u003cp\u003esimply select the correct printer and click the Save icon \u003c\/p\u003e\u003cfigure class=\"image\"\u003e\u003cimg src=\"https:\/\/makerworld.bblmw.com\/makerworld\/model\/DSM00000002723221\/design\/257c5a6ad3cab0f6.png\"\u003e\u003c\/figure\u003e\u003ch2\u003eFinal Note\u003c\/h2\u003e\u003cboostme\u003e\u003cboosttitle\u003eBoost Me\u003c\/boosttitle\u003e\u003cboostcontent\u003eIf this preset helped you, I’d really appreciate a boost!\u003cbr\u003eI’ll also be sharing painted miniatures made with this profile soon.\u003c\/boostcontent\u003e\u003c\/boostme\u003e\u003cp\u003e \u003c\/p\u003e\u003ch2\u003eAI Disclaimer\u003c\/h2\u003e\u003cp\u003eAI was used for \u003cstrong\u003egrammar and spelling corrections\u003c\/strong\u003e.\u003cbr\u003eThe thumbnail has been adjusted for better visibility results will stay the same)\u003c\/p\u003e\u003cp\u003eDesign by Teimo on MakerWorld (license: BY-SA).\u003c\/p\u003e","brand":"Mymadmanlab","offers":[{"title":"Default Title","offer_id":67396793073968,"sku":null,"price":4.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0987\/0809\/5280\/files\/0_f8571586-6f49-4100-ba18-e4d9e7922174.png?v=1784854352","url":"https:\/\/mymadmanlab.com\/products\/ultimate-miniature-figurine-settings-0-4-0-2","provider":"Mymadmanlab.com","version":"1.0","type":"link"}